Whirlpool Washer Making Loud Noise During Wash Cycle (Fix)

Washing machines are usually very noisy and can easily scare people. Slowly and gradually, you might get used to it.

However, sometimes the noise may become severe and sound very different from what it normally does. If your washer is comparatively old, something fishy is going on.

From my own experience, I can say that a loud Washing machine, especially during the wash cycle, is a problem that you need to investigate. My Whirlpool washer has produced quite a few problems in its ten years life.

Therefore, I can give you some good insight into why your washer makes so much noise. Here are some tools that you will require to fix the problem at home:-

1. Flathead screwdriver 
2. Screwdriver 
3. Drill
4. Hammer
5. Screws

How To Fix A Whirlpool Washer Making Loud Noise During Wash Cycle?

When a washer makes some weird and loud noises, the chances are that something is broken within the machine. In most cases, you will need to disassemble the washer and find the root cause of the problem. 

It can also be caused by something as small as too much load. However, you should cover all aspects of your washer to eliminate any bad news that might pop out in the future.

If your washer makes too much noise during the wash cycle, you must look for the root cause and fix the problem as soon as possible. Here are some top reasons why your washer has suddenly become so noisy and how you can fix it.

1. Problems with the drive pulley

The drive pulley is susceptible to damage after extended periods. When this belt has been damaged, there will be a significant amount of noise drying the wash cycle.

To inspect the drive pulley, you need to remove the machine’s outer body to look at the internal components. Next, you must remove all the surrounding components like the pulley belt, the casing, etc.

If the drive pulley appears broken or coated in sediments, it’s time to chuck it. Buy a new drive pulley and replace it immediately before reassembling the washer.

2. Broken or worn-out drum bearings

Failed drum bearings are a common issue for old washing machines. Drum bearings are the first to fail because they go through a lot of stress when the machine is operating.

These drum bearings also give out naturally when the machine has been used for a long time. Cracks, fractures, or breaks may make these drum bearings unfit for continued use.

To replace drum bearings on a washer, you must disassemble the entire machine. This process will require hours, and you should watch detailed tutorials to know how to do it.

3. The washer has been overloaded

An overloaded washer will produce problems like too much noise. Every washer has a load capacity.

You must be mindful of this load capacity when using a Whirlpool washer. If you put in too many clothes, the washer will be thrown off balance, leading to loud noises during the wash and spin cycles.

You can instead stop the machine and take out excess load before starting it again. In some whirlpool models, an indicator showing machine overloading will inform you about the issue.

4. The motor coupling is damaged

A damaged coupler is also one of the top reasons your washer makes so much noise. The coupler is located at the bottom of the washer behind the motor. 

To access this section, you need to take apart the exterior parts of the machine, including the control panel. Then, you need to disconnect the wires and the drain pump from the motor before dislodging it.

The coupler will be located in the center of the drain pump. You must purchase new couplers and replace the old ones to solve the issue.

How Long Do Whirlpool Washers Last?

Whirlpool washers usually tend to last for about ten years. However, proper maintenance work can last up to 13 years.

Luckily, you may have a long-lasting washer that stays for a long time.

There is no guarantee your washer will live as long as ten years. If you use it frequently and don’t shell out money for repair work, your washer might break down after six years or earlier.

Is It Cheaper To Repair Or Replace A Whirlpool Washing Machine?

If your washing machine is relatively newer than eight years, it’s better to repair it and save money. However, for older washers, discarding them and buying a new one will be better.

Since washers usually last for ten years, people tend to make repairs on them as long as possible. However, I think it’s better just to discard them after they run for eight years.

Repairs after this will be pointless because you constantly replace broken and damaged parts. The costs will add up quickly and become a burden for you.

Can I Fix My Whirlpool Washing Machine Myself?

Yes, it is entirely possible to fix your Whirlpool Washer by yourself. You can simply follow the user manuals and YouTube tutorials to know how to fix any problem with your washer.

Fixing a washer at home is quite a difficult task. However, it is not impossible and can be done without calling a professional. 

Since professionals charge so much money to fix a washer, it’s best if you attempt to do it yourself. Sure, it’s a little time-consuming, but it will also save you a lot of money in the long run.

There are plenty of tutorials for amateurs, so you can look them up and fix the washer yourself. However, if you are not confident about your skills, it’s better to call someone else.

Final Remarks

I’m sure now you know why your washer might be making so much noise. If you are lucky, it’s a simple fix that requires a lot of money.

However, if it’s a failed drum bearing or drive pulley, you will spend a lot of time fixing it. To avoid problems like this, I strongly advise you to follow the load instructions and maintain them.

If you still face noise problems, there are always solutions to these issues at home. Here are some of the possible solutions that I’ve talked about in this article:-

1. Repair or replace the drive pulley
2. Replace the drum bearings
3. Reduce the load in the washer
4. Examine the motor coupling