Now, Whirlpool washers are still pretty hot on the market like before. They have taken a lot of care to include error codes in their washers so that people know when there is an issue.
When the F6 E1 error code flashes on the screen, it indicates a system error within the machine. Usually, the control board cannot communicate with the motor.
Now, the result of this fault would be a stagnant washer that doesn’t move. If you are facing such an error, you must read this article.
I will detail the steps to solve the issue for your benefit. Here is a list of tools you may need:-
- 1/4 inch socket driver
- Flathead screwdriver
- Gloves
How To Fix F6 E1 Error On Whirlpool Washer?
\e
While some of these fixes are relatively easy, some might be challenging. If your washer keeps displaying this code, here’s what you should do.
1. Reset The Washer
In most cases, the error code might be displayed due to a glitch. There may be a minor connectivity issue between the central control unit and the motor.
Fixing this issue is extremely easy. All you have to do is unplug the machine and let it sit.
After about five minutes, you can plug it back in and restart the washer. Please put it on a small wash cycle to check for further problems.
If the error code doesn’t flash again, continue using the washer as usual. However, if the error code is back, I recommend you move on to the next possible problem.
2. Replace The Motor Control Unit
If the error code does not result from a glitch, there may be something wrong with the motor control unit. You might need to replace the unit to make your washer work.
One of the primary reasons for the F6 E1 error code is the failure of the motor control unit. This unit may have short-circuited due to an overloading problem.
You need to gain access to the washer to check the unit. Remove the screws from the back panel to find the motor control unit.
It will be located within a box on one side of the tub. Check the motor unit to make sure all the wires are connected.
If you find any loose wires, connect them back to the unit. Next, run a fresh cycle to see if the problem is solved.
Also, check the unit to see if you can spot burnt wires or parts on the motor control. If you do, the unit needs to be replaced immediately.
You can order the motor control set online or offline and replace the old one. It won’t be very complicated so you can do it yourself.
However, I recommend using gloves and ensuring the washer is unplugged. Also, remember to take pictures of the wires to know what goes where.
3. Replace The Central Control Unit
If the motor control isn’t the problem, your central control unit may be faulty. This is a common cause in older washers.
With time, all washer parts will face damage. The central control is also susceptible to all kinds of damage.
You will find the central control unit on the top panel of a washer. To access the unit, you have to remove the outer panel entirely.
When the problem is with the central unit, it is rather severe. I would not recommend trying to fix it on your own.
You may be able to find burn marks on the unit in case of a short circuit. However, it’s best to call a professional for the final diagnosis.
Additionally, it would be best if you remembered that replacing the central control unit is expensive. It would be best if you decided after careful consideration.
If your washer is old, I suggest changing the entire machine. It will be more cost-effective since newer problems will keep cropping up.
How To Solve The E1 Error On A Whirlpool Washing Machine?
You should check your house’s water pressure if you get an E1 error on your washer. Additionally, ensure the inlet valve is not clogged, and the water faucet is open.
An E1 error on a washer means the water levels inside the machine are not adequate. This also means that there needs to be more water to start a wash cycle and clean your clothes efficiently.
You must restore it immediately if the cause lies in adequate water pressure. Also, check if the water faucet has been turned on for the washer.
Check the water inlet valve for clogging if the problem persists. The clogged valve needs to be cleaned so the water can flow into the machine on time.
How Do I Clear An Error Codes On Whirlpool Washers?
To clear an error code on your Whirlpool washer, you must press the start/pause button twice. This will reset the cycle and make the machine work.
When an error code is displayed, the washer will stop working. In this case, you must solve the error and restart the machine.
There is a straightforward way to eliminate the error code once the issue is dealt with. You must press the pause/start button once to clear the code and twice to restart.
How To Reset A Whirlpool Washer Without Unplugging It?
To reset a Whirlpool washer without unplugging it, you must press the start/pause button twice before selecting the power button.
This action will reset the washer for you. Alternatively, you can use the wash setting knob to reset the machine.
When the washer is on, turn the nob one left and then thrice the rice. Finally, turn it once left again.
You will see that all the lights on the panel have lit up together. The washer will run a diagnostic cycle and will be reset completely.
Final Remarks
You now know that fixing an F6 E1 error is not that difficult. Of course, it will only be straightforward if the problem is with central control.
However, that is rarely the case, and it’s usually a glitch or faulty motor control. Make sure you stop overloading your washer to prevent this problem.
If you have missed anything, here’s a quick recap.
Fixes for Whirlpool washer F6 E1 error code:-
- Reset The Washer
- Replace The Motor Control Unit
- Replace The Central Control Unit
My name is Rick Kinney and I am the founder of ExHandyman. I have worked as a handyman for many years, and fixing stuff is my greatest pleasure in life.