Whirlpool Duet washer has been a godsend. The house of Whirlpool has put some serious effort into creating this beauty that has won people’s hearts.
It cleans clothes like magic and even has some great features that other washers lack. However, this washer needs proper maintenance, just like any other appliance.
The washer pump especially needs some good cleaning periodically. This helps to keep your washer in good health and avoid problems like water leakage and drainage issues.
If you are someone who wants to clean the washer pump at home, this article will be super helpful. Here are some of the tools you may need to establish this task:-
- Screwdriver
- Gloves
- Empty tray or bucket
How To Clean The Pump On A Whirlpool Duet?
Washer pumps can be cleaned by removing the filter from under the tub. To achieve this, you need to take out the outer casing and gain access to the parts inside the washer.
Cleaning a washer pump is more accessible. It is a straightforward process and doesn’t require help from a professional.
You can do it at home, which will only take an hour to complete. However, you will require guidance beforehand if this is your first time doing it.
Here are the detailed steps to quickly clean your Whirlpool Duet washer pump.
1. Remove The Bolts On The Back Case
The first step in cleaning the pump on a washer would be to remove the cover. Since the pump and filter will be inside the washer, you must remove the outer casing.
Always make sure the washer is unplugged from the power outlet. If it stays plugged, there may be chances of electrocution.
It would be best if you used a screwdriver to unscrew the bolts and take them out. The screws will line the outer area of the casing on the back of the washer.
After the screws are removed, you can take out the casing and set it aside. Remember to store the bolts properly because you will need them during assembly.
2. Locate The Pump
Now that you have the outer casing out of the way, proceed to look inside. The tub, motor, and pump will be visible pretty clearly.
The pump will be attached to the base of the tub inside the washer. Find a screw or holder on the pump that can be rotated.
This needs to be rotated to unscrew the filter. Be mindful to keep a dish tray or empty vessel below the pump.
Excess water inside the pump may be stuck due to debris. When you screw the pump filter, the water will be released, and it may cause flooding.
3. Unscrew The Filter
Once you have located the filter, start to unscrew it gently. If your tray fills with water, put the filter back and drain the water.
When all the blocked water has been emptied, pull out the filter. It will be easy to do so.
You will notice a lot of dirt and debris if you still need to clean it. Clean the pump filter properly before reattaching it to the tub.
In the end, slowly start your reassembly of the washer. Since the process is simple enough, it will take a little time.
How Do You Get To The Drain Pump On A Whirlpool Duet?
Remove the outer casing on the back to reach the drain pump on a Whirlpool Duet washer. The pump will be located below the tub at the base of the washer.
As I’ve said, the drain pump is never visible on a washer. The same goes for the Whirlpool Duet washer.
The drain pump will be located below the tub on this front-load washer. It will be connected to a drain pipe that takes out the dirty water.
While you can access the drain pipe outside, the pump lies inside. It removes the dirty water from the tub and throws it out of the machine through the pipe.
Where Is The Lint Trap On A Whirlpool Duet Washer?
The lint trap on a Whirlpool Duet washer is located at the bottom of the appliance. Inside the washer, you will find the lint trap below the tub.
Not all washers contain lint traps. However, the duet washer filter includes one; let me tell you, it’s highly beneficial.
This part captures stray lint from clothes and collects it at the filter. You will need to clean the filter, so the lint doesn’t circulate back into the washer.
I was skimming through the debris at least once in 4 months. It will be located on the filter, so you can access it by removing the back casing.
How Do I Know If My Washing Machine Pump Is Clogged?
If your washer pump is clogged, it won’t drain as well as it should. Additionally, there might be water leakage issues from the washer.
The most obvious sign of a clogged pump would be leftover water in the washer. You may find your clothes soggier due to too much staying behind.
When the water cannot escape through the drain pipe, it will flow back into the machine. Your clothes will then absorb the water and appear soggier.
You may also face severe leakage issues if the clog develops too much. If you are not careful enough, your home will face water damage from the machine.
Additionally, you may find your clothes need to be cleaned. This is because the dirty water cannot flow out of the machine through the pump and drain pipe.
Final Remarks
So, I was able to clear your doubt. You should now know much more about cleaning a washer pump than before.
Always check for a clog and clean the filter once every four months. Leaving it dirty will result in a clog and cause water leakage.
If you have missed anything from this article, here’s a quick recap.
Steps to clean the Whirlpool Duet washer pump:
- Remove The Back Casing
- Locate The Pump
- Unscrew The Filter
My name is Rick Kinney and I am the founder of ExHandyman. I have worked as a handyman for many years, and fixing stuff is my greatest pleasure in life.