F3 E2 Whirlpool Oven error code means that there may be a problem with the Oven Temperature Sensor, the Warming Drawer Sensor, or the associated wiring.
Whirlpool Ovens is a reliable appliance in the fast-paced life and are among the best and most reliable brands of dryers. Whirlpool dryers have 12 to 15 years, and some may last longer if you maintain them properly.
Usually, people face almost no problem while using the Whirlpool ovens because of their user manuals that have explained the whole process in great detail.
But sometimes, it just happens that the oven won’t turn on, or it shows an error code related to the temperature sensors that might indicate overheating the device. Which can also turn into a fire hazard.
However, the oven temperature sensor often gives up due to overheating, and this error code indicates that the electronic oven control board in the range senses an over-temperature condition in the oven.
In this article, we will discuss the F3 E2 Whirlpool Oven error code and how you can fix this error at home with no added service charge.
F3 E2 Error Code Meaning
The F3 E2 Whirlpool Oven error code generally means that there may be a problem with the Oven Temperature Sensor, the Warming Drawer Sensor, or the associated wiring.
The F3 E2 error code is a common problem you might encounter several times during your engagement with the machine.
The code is a combination of two factors:
Fault code F3
The general fault is under code 3 of the issues related to the Whirlpool oven and products. The fault is generally associated with the open oven temperature sensors and indicates the replacement temperature sensors.
Fault code E2
This code defines the specific error and denotes that the exact component has failed, especially a shortened thermistor, and the need to replace it. It is an electrical resistor whose resistance is significantly reduced by heating, used for measurement and control.
In simpler terms, the F3 E2 Whirlpool Oven error code indicates a problem with the oven temperature sensors. For, e.g., the device might not be able to show the correct temperature, often causing overheating in the appliance.
What Causes The F3 E2 Error Code?
The Whirlpool washer F3 E2 error code is a temperature sensor error.
If the water temperature sensor reading is out of the following range of 14°F to 230°F or 10°C to 110°C, the control will shut down the machine and give you the F3E2 error.
The F3 E2 error code indicates an inlet water temperature fault. If the temperature sensor or the thermistor value is out of range during the water heating step of the wash cycle, it will display the error.
This is caused by a faulty water temperature sensor, negative temperature coefficient, or a wiring fault. This error code can also indicate a heating circuit fault.
You must wear safety gear and always unplug the washer when performing maintenance or troubleshooting. The faulty wiring or temperature sensors can cause further damage to the appliance and you.
How To Fix Error F3E2 On A Whirlpool Oven?
Once you have understood the real cause behind the F3 E2 Error Code, it should be fairly easy to repair.
1. Remove the Philips head screws
The Whirlpool F3 E2 oven error code is due to a bad temperature sensor. Still, fixing or replacing whatever works in your condition is straightforward.
The procedure will take about 30 minutes and can be done quickly at home.
- To pull it away from the cabinet, you can gently pull it out away from the cabinet and then reach in from the back to unplug it.
- Remove the four Philips head screws to get off one of the panels.
- Once you remove one of the panels, you can quickly locate the temperature sensor on the bottom corner of the appliance. The location may be different based on the model but refer to the user’s manual whenever in doubt.
- There will be a couple of Philips’ head screws holding it in, so remove it gently using an angled tool.
- Separate the modular connector that carries the signal and replace it with a new one.
The temperature sensors last about four to five years, so it is normal to change them from time to time whenever the warning sign comes up.
You can get temperature sensors for your Whirlpool oven online or at the nearest hardware store. They cost around 10 USD to 20 USD.
You can also find more expensive sensors for about 60 USD at the hardware store.
2. Close the panel and pop in the screws
- Attach the temperature sensors back and screw the two Philips head screws you took out earlier to ensure they are holding it tight and together.
- Once you have attached the temperature sensor properly, make sure to retrace all your previous steps and reattach everything the way it way.
- Make sure the modular connector makes a click sound that indicates that it has been appropriately placed back in its position.
- To pop the panel back in the counter, slide it into it and press it gently but swiftly till you hear a click sound.
- Plug it back in and test it first.
3. Press the cancel button
Once you have reattached everything back, turn the oven on.
When you turn it back on, the error code PF, meaning power failure, will be displayed.
Press the cancel button to get rid of that, and wait for a minute before turning it off and back on again.
Make sure to run a bake cycle first to test if the oven is now working correctly.
4. Reset the power of the product
In most cases, the oven starts working right on. However, it is still recommended that you reset the power f the product to help the interface in the initialization process.
- Power the unit down by turning off the circuit breaker for one minute.
- Power the unit up by turning on the circuit breaker.
- Monitor the oven for one minute to ensure the error code does not display again.
- Verify oven operation once again.
If you’re having trouble controlling your oven, try resetting the control board. After you’ve unplugged the oven, you can return it to its original position by waiting a minute before plugging it back in.
Final Remarks
F3 E2 Error Code on Whirlpool Oven is quite common. Still, once you have figured out its meaning and real cause, it is reasonably easy to fix it at home with no added costs.
Luckily, despite being a complex machine, there are chances that the problem can be solved at home very easily with several proven fixes:
- Remove the Philips’ head screws and replace the temperature sensor
- Close the panel and pop in the screws
- Press the cancel button
- Reset the power of the product
My name is Rick Kinney and I am the founder of ExHandyman. I have worked as a handyman for many years, and fixing stuff is my greatest pleasure in life.